Quick answer: AERMOD (full form: AMS/EPA Regulatory Model) is the US EPA's preferred air dispersion model for predicting ground-level pollutant concentrations within about 50 km of industrial sources. It is a steady-state Gaussian plume model with three linked programs: AERMET prepares the weather, AERMAP prepares the terrain, and AERMOD calculates hourly concentrations at every receptor. It is free to download from the EPA SCRAM website and is the model Indian EIA and consent studies normally use.
What Is AERMOD?
AERMOD stands for the AMS/EPA Regulatory Model. It was developed by AERMIC, a joint working group of the American Meteorological Society (AMS) and the US Environmental Protection Agency (EPA), and it is the US EPA's preferred model for near-field regulatory dispersion modelling. EPA AERMOD predicts how emissions from stacks, vents, stockpiles, roads and other sources travel through the lower atmosphere, and what concentrations result at ground level around a facility.
In one line: the AERMOD model is a steady-state Gaussian plume dispersion model that estimates pollutant concentrations at receptor locations by combining source emission characteristics, hourly meteorology and terrain, using boundary-layer physics to describe how the atmosphere spreads a plume.
In India, AERMOD modelling (also written AERMOD modeling) underpins the air quality prediction chapter of Environmental Impact Assessment (EIA) reports prepared under the EIA Notification 2006. It supports applications for Environmental Clearance (EC) and for the Consent to Establish (CTE) and Consent to Operate (CTO) issued by State Pollution Control Boards (SPCBs), and it is used to justify stack heights and pollution control equipment. If you are new to the wider subject, our article on what air dispersion modelling is gives the background.
A note on spelling: people often search for the model as "aeromod", "aermode" or "eirmod". The correct name is AERMOD, pronounced "air-mod", written in capitals because it is an acronym. The meteorological and terrain preprocessors are AERMET and AERMAP, again with no extra letters.
Why AERMOD Uses a Gaussian Steady-State Approach
Two terms define how the AERMOD dispersion model calculates.
Steady-state means the model treats each hour of weather as constant for that hour. It computes an hourly concentration at every receptor for that hour, then moves to the next hour and repeats across the full meteorological record, usually one year (8,760 hours) or more. Longer averages, such as 24-hour and annual values, are built up from those hourly results.
Gaussian means the model assumes the concentration across a plume follows a normal (bell-shaped) distribution in the horizontal and, in stable and neutral conditions, the vertical. The width of the bell grows with distance downwind at a rate set by atmospheric turbulence.
This approach captures the dominant physics of near-field dispersion efficiently. Within roughly 50 km of a source it reproduces observed concentration patterns well enough for regulatory decisions, and it runs fast enough to model a full year of hourly weather at thousands of receptors, giving both the short-term peaks and long-term averages that air quality standards require.
The trade-off is that a steady-state model assumes the plume travels in a straight line from the source during each hour. It is not intended for long transport distances, strongly curving or recirculating flows, or pollutants that change chemically over hours. For those cases, Lagrangian puff models such as CALPUFF or Eulerian grid models are more appropriate, as discussed in AERMOD vs CALPUFF for Indian EIA projects.
How the AERMOD Dispersion Model Works: Three Linked Programs
AERMOD is not a single program but a system of linked components. Understanding this structure is the key to understanding how AERMOD works.
| Component | Role | Main inputs | What it produces |
|---|---|---|---|
| AERMET | Meteorological preprocessor | Hourly surface observations, upper-air soundings, surface characteristics | A surface file and a profile file of hourly boundary-layer parameters |
| AERMAP | Terrain preprocessor | Digital elevation model, source and receptor coordinates | Elevations and hill height scales for every source and receptor |
| AERMOD | Dispersion processor | Source data, AERMET files, AERMAP output, receptor grid | Concentrations and deposition at every receptor and averaging period |
A fourth program, BPIP-PRIME, calculates building dimensions for downwash when stacks stand near tall structures. Our knowledge-base article on AERMET, AERMAP and BPIP covers all three preprocessors in more depth.
AERMET: the Meteorological Preprocessor
AERMET converts raw weather data into the boundary-layer parameters the dispersion calculation needs. It reads hourly surface observations (wind speed and direction, temperature, cloud cover) together with upper-air soundings that describe the vertical structure of the atmosphere, or on-site measurements where available.
From these, and from the surface characteristics of the site, AERMET derives:
- Friction velocity, representing mechanical turbulence generated by wind shear near the ground.
- Monin-Obukhov length, a measure of atmospheric stability that shows whether conditions are convective, neutral or stable.
- Convective velocity scale, which characterises buoyancy-driven turbulence during daytime heating.
- Mixing heights, both convective and mechanical, the depth through which pollutants can mix vertically.
- Sensible heat flux, the exchange of heat between the ground and the air.
AERMET also needs three surface parameters for the ground around the site: albedo (reflectivity), Bowen ratio (the balance of sensible to latent heat) and surface roughness length (the aerodynamic effect of vegetation and structures). These must reflect actual land use, which in India varies widely between coastal, urban-industrial, agricultural and forested settings. The EPA's AERSURFACE tool derives these from US land cover data, so Indian studies usually set them from sector-by-sector land use assessment instead. The full process is described in AERMET explained.
AERMAP: the Terrain Preprocessor
AERMAP reads a digital elevation model and assigns an elevation to every source and receptor. For each receptor it also calculates a hill height scale, which AERMOD uses to decide how a plume interacts with rising ground.
Terrain changes ground-level concentrations significantly. Elevated terrain can bring a plume closer to the ground and raise concentrations on hillsides, while valleys can channel winds. For flat coastal or alluvial plain sites AERMAP has little effect, but for projects in the Western Ghats, the Northeast, Chhattisgarh and Odisha mining belts or the Himalayan foothills, terrain treatment is essential. See terrain and land use in AERMOD.
AERMOD: the Dispersion Processor
The AERMOD processor is the core engine. It reads the source data, the processed meteorology and the terrain output, and computes a concentration at each receptor for each hour.
A defining feature is how it handles stability. In stable and neutral conditions it uses a Gaussian distribution in both the horizontal and vertical. In the convective (daytime, well-mixed) boundary layer it uses a bi-Gaussian probability density function in the vertical, which represents the asymmetric updrafts and downdrafts of convective turbulence. This lets AERMOD reproduce the way a daytime plume can be carried to the ground close to a tall stack, which older models handled poorly.
For terrain, AERMOD calculates a critical dividing streamline height for each receptor. Air below that height tends to flow around a hill, and air above it tends to flow over it. The model combines a horizontal plume state and a terrain-following plume state, weighted by this height, so a plume can partly rise over and partly impinge on high ground.
AERMOD also includes algorithms for:
- Plume rise, accounting for the momentum and buoyancy that lift hot exhaust gases above the stack before they level off.
- Building downwash through the PRIME algorithm, capturing how nearby structures create wakes that pull a plume toward the ground. See AERMOD building downwash (BPIP-PRIME).
- Urban effects, through an option that enhances night-time turbulence over a city based on its population.
- Dry and wet deposition of particles and gases.
- NO2 conversion, with methods such as OLM, PVMRM and GRSM, explained in NO2 modelling in AERMOD.
AERMOD vs ISCST3: Where AERMOD Came From
Before AERMOD, the US regulatory standard was the Industrial Source Complex Short Term model, version 3 (ISCST3). AERMIC developed AERMOD through the 1990s to bring current boundary-layer science into regulatory practice. The US EPA adopted AERMOD as its preferred near-field model in late 2005, with a one-year transition, after which ISCST3 was withdrawn as a preferred model. Indian agencies and consultants moved to AERMOD for EIA work over the same period, and it is now the model Expert Appraisal Committees expect unless a study gives a reason to use something else.
| Feature | ISCST3 | AERMOD |
|---|---|---|
| Stability | Six discrete Pasquill-Gifford classes (A to F) | Continuous parameters (Monin-Obukhov length, friction velocity, convective velocity) |
| Dispersion rates | Empirical curves by stability class | Calculated from turbulence profiles that vary with height |
| Convective conditions | Gaussian in the vertical | Bi-Gaussian vertical distribution for updrafts and downdrafts |
| Vertical structure | Single wind and temperature value per hour | Vertical profiles of wind, temperature and turbulence |
| Terrain | Simple and complex terrain treated separately, with cruder algorithms | Unified treatment using the dividing streamline height |
| Building downwash | Older Huber-Snyder and Schulman-Scire methods | PRIME algorithm |
| Surface characteristics | Rural or urban only | Albedo, Bowen ratio and roughness by sector and season |
| Regulatory status | Superseded | Current EPA preferred model |
Some older Indian reports still quote ISCST3 results. For a new study there is no reason to use it, and an older ISCST3 study revised for an expansion is usually best rerun in AERMOD.
AERMOD Versions and Updates
The EPA updates AERMOD, AERMET and AERMAP regularly, usually around once a year. Versions are numbered by year and day of release, so version 24142 was released on day 142 of 2024. Each release fixes bugs, refines options and occasionally changes results slightly, so two practices apply:
- Use the current EPA release for a new study, and name the versions of AERMOD, AERMET and AERMAP in the report.
- Keep the same version within one project. If a study is revised after a new release, either rerun everything on the new version or record why the original version was kept.
AERMOD Download: What the EPA SCRAM Package Contains
The official AERMOD download is on the US EPA's Support Center for Regulatory Atmospheric Modeling (SCRAM) website, under the preferred and recommended air quality dispersion models. It is free, needs no licence or registration, and is the same model that commercial interfaces run underneath. Cost and what paid packages add are covered in is AERMOD free?.
| Item | What it is | Where it comes from |
|---|---|---|
| AERMOD executable | Compiled program for Windows, run from a command prompt | AERMOD page on SCRAM |
| Fortran source code | For compiling on Linux or other systems | AERMOD page on SCRAM |
| User's guide | Every keyword on every pathway, with syntax | AERMOD page on SCRAM |
| Model formulation document | The physics and equations | AERMOD page on SCRAM |
| Model change bulletin | What changed in each release | AERMOD page on SCRAM |
| Test cases | Sample input and output files to check an installation | AERMOD page on SCRAM |
| AERMET and AERMAP | Separate downloads, each with its own guide | Related programs on SCRAM |
| BPIP-PRIME, AERSURFACE, AERSCREEN, AERMINUTE | Supporting programs | Related programs on SCRAM |
Two points matter for Indian users. AERSURFACE and AERMINUTE are built around US land cover and US airport one-minute wind data, so they rarely apply directly in India. And the package contains no graphical interface, no maps and no weather data: you supply the meteorology, terrain and source data, write the control files by hand, and turn the outputs into maps yourself.
The AERMOD Input File, Pathway by Pathway
The AERMOD input file is a plain-text control file, conventionally named aermod.inp. It is organised into five pathways, each a block of lines beginning with a two-letter pathway code, a keyword and its parameters. Each pathway opens with STARTING and closes with FINISHED. The table below describes the main keywords as an illustrative outline rather than a working file.
| Pathway | Main keywords | What they set |
|---|---|---|
| CO (control) | TITLEONE, MODELOPT, AVERTIME, POLLUTID, URBANOPT, RUNORNOT | Run title; regulatory default options and whether terrain is elevated (ELEV) or flat (FLAT); averaging periods such as 1, 24 and annual; pollutant name; urban option with population; whether to run or only check the file |
| SO (source) | LOCATION, SRCPARAM, BUILDHGT and related building keywords, EMISFACT, URBANSRC, SRCGROUP | Source type, coordinates and base elevation; emission rate, release height, exit temperature, velocity and diameter; downwash dimensions from BPIP-PRIME; emissions that vary by hour or season; which sources are urban; how sources are grouped in results |
| RE (receptor) | GRIDCART, GRIDPOLR, DISCCART, ELEVUNIT, INCLUDED | Cartesian or polar grids; discrete receptors at villages, schools, hospitals and monitoring stations; elevation units; inclusion of the receptor file written by AERMAP |
| ME (meteorology) | SURFFILE, PROFFILE, SURFDATA, UAIRDATA, PROFBASE, STARTEND | The AERMET surface and profile files; station identifiers and years; base elevation of the met tower; the start and end dates to model |
| OU (output) | RECTABLE, MAXTABLE, DAYTABLE, PLOTFILE, POSTFILE, RANKFILE, SUMMFILE | Which ranked values to report, which files to write for mapping and post-processing |
An illustrative outline of a simple single-stack study in prose: the control pathway names the project, selects regulatory default options with elevated terrain, requests 1-hour, 24-hour and annual averages and names the pollutant as SO2. The source pathway defines one point source at its UTM coordinates with a base elevation from AERMAP, an emission rate in grams per second, a stack height in metres, an exit temperature in kelvin, an exit velocity in metres per second and an internal diameter in metres, then groups it into a source group called ALL. The receptor pathway includes the AERMAP receptor file, which holds a nested Cartesian grid plus discrete receptors. The meteorology pathway points to the AERMET surface and profile files for the study year. The output pathway asks for the highest and second-highest values for each averaging period, a table of the 50 highest values, and plot files for each averaging period.
A reviewer reading the control file will check the averaging periods, ELEV or FLAT terrain, the urban option, the receptor layout and the meteorological period, and each choice should be explained in the report. A practical list of what you need before starting is in the AERMOD input data checklist.
Source Types AERMOD Can Model
AERMOD represents real emission sources with a small set of geometric types:
- Point sources for stacks and vents, with plume rise, so exit temperature and velocity matter as much as emission rate.
- Area sources for emissions spread over a surface, such as stockpiles, open yards, lagoons and landfill faces, in rectangular, circular and polygon shapes.
- Volume sources for emissions that start out mixed through a volume, such as conveyor transfer points, building vents and crushing plants.
- Line and road sources for haul roads and traffic, including RLINE options for roadways.
- Open pit sources for mines and quarries, where the pit walls hold part of the emission back.
- Buoyant line sources for long, hot roof lines such as aluminium smelter potlines.
Most Indian industrial studies combine point sources for stacks with area or volume sources for fugitive dust. Leaving out fugitive sources is one of the most common reasons a study under-predicts PM10 near the boundary. Each type is explained with examples in AERMOD source types explained.
AERMOD Output: What the Model Produces
Every run writes a main output file. It echoes the input, lists warnings and errors, and gives result tables for each source group and averaging period. The OU pathway controls what else is written.
| Output keyword | What it gives | Typical use |
|---|---|---|
| RECTABLE | The highest, second-highest (and so on) value at every receptor for each short-term averaging period | Design values and checks at specific receptors |
| MAXTABLE | A ranked list of the overall highest values across all receptors, with the receptor location and date | Finding the maximum ground-level concentration and when it occurred |
| DAYTABLE | Results for every receptor for each day | Detailed review of particular days, used sparingly because files grow large |
| PLOTFILE | A text file listing each receptor's coordinates and its chosen ranked value | Drawing isopleth (contour) maps in GIS or plotting software |
| POSTFILE | Every concentration at every receptor for every averaging period | Post-processing, percentiles, frequency analysis and custom statistics |
| RANKFILE | Ranked values for comparison between models or scenarios | Model comparison and quantile plots |
| SUMMFILE | A summary of the highest values without the full output | Quick checks across many runs |
In plain terms, MAXTABLE tells you the worst value and where and when it happened, PLOTFILE gives the data for the map, and POSTFILE gives everything, for statistics the standard tables do not provide.
For an Indian EIA, these outputs become:
- The maximum predicted incremental ground-level concentration for each pollutant and averaging period.
- The location, distance and direction of that maximum from the source.
- Isopleth maps of concentration contours over the study area.
- Predicted increments at each monitoring station and sensitive receptor.
- Totals formed by adding modelled increments to measured baseline concentrations, compared against the National Ambient Air Quality Standards (NAAQS) notified by the CPCB.
How to read these tables and maps is covered in how to read AERMOD output, and how to draw the maps in AERMOD isopleth maps in QGIS. The choice of averaging periods and how each maps to a NAAQS limit is explained in AERMOD averaging periods and NAAQS compliance.
How to Run AERMOD: Step by Step
The sequence is the same with the EPA programs or a software interface.
- 1Define the study. Fix the pollutants, averaging periods, modelling domain (usually 10 km around the site) and the coordinate system, normally UTM.
- 2Build the emission inventory. For each source, gather location, stack height, diameter, exit temperature, exit velocity and emission rate in grams per second, plus fugitive source dimensions. See how to prepare an emission inventory.
- 3Prepare meteorology. Obtain hourly surface data and upper-air data for a representative station and year, set albedo, Bowen ratio and roughness by sector, and run AERMET to produce the surface and profile files. The loss of NOAA's legacy ISD archive in 2025 makes this step harder; see NOAA ISD stopped in 2025.
- 4Lay out receptors. Design a nested grid with closer spacing near the source plus discrete receptors. See receptor grid design.
- 5Process terrain. Run AERMAP with a digital elevation model such as SRTM to give elevations and hill height scales.
- 6Process buildings. Run BPIP-PRIME if stacks are near structures tall enough to cause downwash.
- 7Write the control file with the five pathways, and run with RUNORNOT set to NOT first to check syntax.
- 8Run AERMOD, then read the main output file for warnings, errors and the count of calm and missing hours.
- 9Post-process. Extract maximum values, add baseline concentrations, draw isopleths and prepare the tables.
- 10Check and report. Review inputs and results against the checks in 10 common AERMOD mistakes, then write the modelling chapter.
Worked Example: A Single Boiler Stack
The numbers below are illustrative only, chosen to show the method rather than to represent any real project.
A plant proposes a coal-fired boiler with one stack. The inputs are: stack height 60 m, internal diameter 2.0 m, exit temperature 413 K, exit velocity 15 m/s, SO2 emission rate 12 g/s. The site is on flat agricultural land, so a rural setting is used; terrain is processed through AERMAP but varies only a few metres. One year of hourly meteorology is processed through AERMET. Receptors run at 100 m spacing out to 2 km and 500 m spacing out to 10 km, with discrete receptors at eight monitoring stations.
The illustrative results:
| Averaging period | Maximum increment (µg/m³) | Location of maximum | Highest baseline at monitoring stations (µg/m³) | Predicted total (µg/m³) | NAAQS (µg/m³) |
|---|---|---|---|---|---|
| 24-hour | 9.5 | 1.4 km east-northeast | 14.0 | 23.5 | 80 |
| Annual | 1.8 | 1.6 km east-northeast | 9.0 | 10.8 | 50 |
Here the total is well within the standard. A real report also adds the increment at each monitoring station to the baseline measured there; the worst-case combination shown above is a conservative check. If totals approached the limit, the next steps would be to test a taller stack, lower emission rate or added controls, and rerun. For how stack height changes the answer, see stack height and ground-level concentration.
Typical Settings for AERMOD Modeling in India
There is no single correct configuration, but a well-built Indian EIA or consent study usually looks like this:
- Meteorology: one year (or one season, where the EIA baseline season is used) of hourly data for the site, with surface data from a representative station, on-site monitoring or validated reanalysis, upper-air data or a documented substitute, and site-specific albedo, Bowen ratio and roughness. See meteorological data for air modelling in India.
- Terrain: elevated terrain switched on, using SRTM or similar elevation data processed through AERMAP.
- Receptors: a nested grid out to around 10 km, plus discrete receptors at every monitoring location and sensitive place named in the study.
- Building downwash: BPIP-PRIME for every stack lower than about two and a half times the height of nearby buildings.
- Averaging periods: 1-hour and 8-hour for CO; 24-hour and annual for PM10, PM2.5, SO2 and NO2, matching the CPCB NAAQS. See NAAQS in India explained.
- Results: maximum incremental concentrations, their locations, isopleth maps and the total of increment plus baseline at each monitoring station, compared with the NAAQS.
How AERMOD Fits the Indian Regulatory Process
Within an EIA prepared under the EIA Notification 2006, the air environment chapter uses AERMOD to predict the incremental impact of a proposed facility: baseline air quality is measured over a season, the emission inventory is compiled, AERMOD is run with site-representative meteorology and terrain, increments are added to baseline values, totals are compared with the NAAQS, and stack heights, controls or mitigation are recommended where predictions approach the limits. The Expert Appraisal Committees of the Ministry of Environment, Forest and Climate Change (MoEFCC), or the state-level committees for category B projects, review this chapter. The same modelling supports CTE and CTO applications to SPCBs. For the EC context see air quality modelling for Environmental Clearance.
How AERMOD Fits US EPA Regulatory Modeling
In the United States, AERMOD is the preferred near-field dispersion model in the EPA's Guideline on Air Quality Models, published as Appendix W to 40 CFR Part 51. It is the default for estimating concentrations from industrial sources out to roughly 50 km, and most State permitting agencies expect it unless an alternative model is justified and approved. The 2017 revision of Appendix W confirmed AERMOD's role and removed CALPUFF as the preferred long-range model (see AERMOD vs CALPUFF).
The most recent revision was signed on 20 November 2024 and published in the Federal Register on 29 November 2024 (89 FR 95034), with an effective date of 28 January 2025. It updated parts of AERMOD's scientific formulation and refined the guidance on how background concentrations are determined for NAAQS modeling. Always run the model version and regulatory options your reviewing agency currently accepts, and check the EPA SCRAM site for later releases.
Where AERMOD is used in US permitting:
- Prevention of Significant Deterioration (PSD) permits for new or modified major sources, to show compliance with the NAAQS and PSD increments.
- Minor source and State permits, where many States require modeling above their own emission thresholds.
- SO2 designations and State Implementation Plans, where modeled design values are compared with the 1-hour SO2 standard.
Statistics that matter in US reviews. The short-term US standards are written as percentiles: the 1-hour NO2 standard uses the 98th percentile of daily maximum 1-hour values averaged over three years, and the 1-hour SO2 standard uses the 99th percentile, also averaged over three years. AERMOD reports these directly when you request the right ranks. Appendix W calls for five years of representative National Weather Service meteorology processed through AERMET, or at least one year of site-specific data.
1-hour NO2 follows a tiered approach. Tier 1 assumes all NOx converts to NO2, Tier 2 applies an ambient ratio (ARM2), and Tier 3 uses detailed chemistry options such as OLM and PVMRM. Our guide to AERMOD NO2 modelling and NOx conversion explains how each tier changes the result, and AERMOD averaging periods covers how ranks and percentiles map to a standard.
AERMOD Limitations and When Not to Use It
AERMOD's accuracy is discussed in how accurate is AERMOD?, but in short it performs best at predicting the highest concentrations over a year, not the exact concentration at a given place and hour. Its main AERMOD limitations follow from its design.
| Limitation | Why it arises | What to use or do instead |
|---|---|---|
| Distances beyond about 50 km | Straight-line plume assumption breaks down as winds change over long travel times | CALPUFF or a grid model |
| Calm and very low winds | Calm hours are skipped, and low-wind dispersion is uncertain | Document calm hours; consider puff models where calms dominate |
| Coastal sites with sea breeze and shoreline fumigation | One wind field per hour cannot represent a land-sea boundary | CALPUFF with a three-dimensional wind field, or a documented justification |
| Complex valley flows and night-time pooling | Flow is not steered by terrain in the way real valley winds are | CALPUFF or more detailed flow modelling |
| Secondary pollutants (sulphate, nitrate, ozone, most secondary PM2.5) | No full atmospheric chemistry; only simple NO2 schemes and decay | Photochemical grid models such as CMAQ or CAMx |
| Accidental or short releases of toxic or dense gases | Steady-state hourly treatment, no dense-gas physics | ALOHA, PHAST or dedicated dense-gas models |
| Street canyons and flow around complex buildings | Downwash handles wakes, not detailed urban geometry | CFD or street-canyon models |
| Indoor or occupational exposure | Designed for outdoor ambient air | Indoor air or workplace exposure methods |
The other limit is the data: AERMOD will run with poor meteorology, wrong roughness or a missing fugitive source and still produce precise-looking numbers. Most failed studies fail on inputs, not physics. For choosing between model types, see choosing an air dispersion model.
Running AERMOD: Software Options
AERMOD itself is free. What costs time is everything around it: preparing meteorology through AERMET, extracting terrain through AERMAP, laying out receptors, running BPIP-PRIME, and turning plot files into maps and tables. Most studies therefore use one of three routes:
- 1The EPA programs directly, with control files written by hand and outputs processed in a spreadsheet or GIS. Lowest software cost, highest skill demand.
- 2A commercial desktop interface, such as Lakes Environmental AERMOD View or Trinity Consultants BREEZE AERMOD, which wraps the same EPA model in a graphical front end with mapping. These are licensed per seat.
- 3A browser-based service. Our AERMOD software, AERMOD Studio, runs US EPA AERMOD and AERMET on a server, prepares the meteorology, and produces GLC tables, isopleths and an EIA-format report. Its current scope is point sources over flat terrain, and a free demo is available. How online running works is explained in AERMOD online, and a comparison of tools in air quality modelling software used in India.
How DSTechnoverse Helps
DSTechnoverse runs regulatory AERMOD studies for Environmental Clearance, Consent to Establish, expansions and stack height justification, delivered remotely across India, either directly for project proponents or as white-label work for EIA consultancies. Our AERMOD air dispersion modelling service covers meteorology, terrain, receptors, modelling and the report chapter. If you prefer to run models yourself, AERMOD Studio gives you US EPA AERMOD in a browser, and firms wanting their own configured tool can see our AERMOD software provider page. To discuss a project or request a demo, contact us.
Further Reading
- AERMOD online: running the EPA model in a browser
- Is AERMOD free? EPA download, paid interfaces and the real costs
- AERMOD vs CALPUFF for Indian EIA projects
- AERMET explained: preparing meteorological data for AERMOD
- Building downwash in AERMOD (BPIP-PRIME)
- How to read AERMOD output and contour maps
- 10 common AERMOD modelling mistakes
- AERMOD air dispersion modelling service
Frequently Asked Questions
What does AERMOD stand for? AERMOD stands for the AMS/EPA Regulatory Model, developed by a working group of the American Meteorological Society and the US Environmental Protection Agency.
Is AERMOD free to use? Yes. The US EPA distributes the AERMOD, AERMET and AERMAP programs and their source code free of charge. Commercial software packages add a graphical interface and mapping on top of the same model.
How far from the source can AERMOD be used? AERMOD is intended for near-field assessment, typically up to about 50 kilometres from the source. Beyond that, or where wind fields vary strongly across the domain, a model such as CALPUFF is more suitable.
What is the difference between AERMOD and CALPUFF? AERMOD is a steady-state Gaussian plume model that treats each hour of weather as uniform across the domain. CALPUFF is a puff model that follows releases through changing wind fields, which suits long distances, coastal sites and calm conditions.